Catcher processors can use their daily production reports to create and populate landing reports and fish tickets.
NOTE: This consolidated landing report option is not to be used by motherships.
1. After production reports have been created, go to File....New and choose Consolidated as Type of Report.
Click OK.
2. Choose a date range for which you would like to create a consolidated landing report, based on your
production report entries. This could be done weekly, or for a whole trip. Click OK.
3. Enter the crew size of the fishing crew for this date range, which includes the skipper but not observer or the
production crew. You'll notice all of the management programs for the data range you entered are listed as
separate rows. Highlight one row at a time and click on the Enter CFEC Permit button to enter permit
information for that management program.
4. A Permits dialog box will open with an illustration of a CFEC permit card.
The CFEC permit has three parts:
i. Fishery, for example K91o
ii. Permit: 5-digit number with a check digit (letter); for example, 12345N
iii. Year sequence: 4 numbers plus a check letter, for example 0501x. The first 2 digits of this sequence
are the year that the permit is issued. The next two digits is the card number (ex: the fisherman lost his first
card so it may say 02)
Enter permit information in the fields supplied. The Mag Stripe field is to be used if you have a magnetized
CFEC card and a card swiper. If you do not have a magnetized card and swiper, leave the Mag Stripe field
blank. Click OK.
5. Highlight the next row of a different management program and click on the Enter CFEC Permit button again.
Repeat step #4 again. You'll need to repeat these steps again until you have entered permit information for all
management programs listed for the specified date range.
When you are finished entering permit information for all management programs listed for the specified data
range, click on the OK button. Otherwise the Cancel button will delete all your permit entries.
Separate landing reports will be created for each management program and for each gear type listed. The
screen shot below shows one of the three landing report created.
For the Vessel/Location/Status tab, verify the header information that has been filled out, based on your
entries on your production reports for that date range, gear type, and management program.
b. ADF&G processing code (purchaser/owner): is preloaded from your selected operation. If you want to
change it, then choose the appropriate code from the dropdown.
c. ADF&G Processor Code (custom processor): If you are doing custom processing then you will need
your processing code here and the F-code of the company you are processing for as the purchaser/owner.
d. Port of Landing: catcher processors use: FCP.
Permits & Pounds
Click on the Permits & Pounds tab shown in the screen shot above.
a. Verify the CFEC permit information is correct. If you must make changes to the CFEC permits entered,
highlight a row and click on the Open button.
NOTE: Do not make changes to the management program or management program ID without also making the
same changes to your production reports off of which your landing report is based. Changing your landing
report does not automatically make the same changes to your production report.
Vessel/Location/Status
A Permits dialog box will open where you can make changes to your entries. Click OK.
For the Vessel/Location/Status tab, verify the header information that has been filled out, based on your
entries on your production reports for that date range, gear type, and management program.
b. ADF&G processing code (purchaser/owner): is preloaded from your selected operation. If you want to
change it, then choose the appropriate code from the dropdown.
c. ADF&G Processor Code (custom processor): If you are doing custom processing then you will need
your processing code here and the F-code of the company you are processing for as the purchaser/owner.
d. Port of Landing: catcher processors use: FCP.
Permits & Pounds
Click on the Permits & Pounds tab shown in the screen shot above.
a. Verify the CFEC permit information is correct. If you must make changes to the CFEC permits entered,
highlight a row and click on the Open button.
NOTE: Do not make changes to the management program or management program ID without also making the
same changes to your production reports off of which your landing report is based. Changing your landing
report does not automatically make the same changes to your production report.
A Permits dialog box will open where you can make changes to your entries. Click OK.
Itemized Catch
Make sure your itemized catch is correctly assigned to your permits. If you wish to edit the weight or number of
animals assigned to a permit, highlight a line of itemized catch and click on the Open button.
An Itemized Catch dialog box will open and you can edit weight or number of animals reported, or you may add
grading and pricing information. Grading and pricing is not required on these reports.
When you are finished entering information for the line item, click on the OK button to accept changes. The
Cancel button cancels the change and the Remove button removes grading and pricing information for that line
item when the row is highlighted.
NOTE: Do not make changes to the weights or numbers of animals without also making the same changes to
your production reports off of which your landing report is based. Changing your landing report does not
automatically make the same changes to your production report.
Statistical Areas: You can leave the Statistical Areas worksheet blank since you've already entered this
information on your production reports. The statistical areas appear as a field in the line items.
Once you have saved your consolidated report, go to Reporting....Transmit Reports to transmit that report.
Please email the transmission file to elecrep@noaa.gov. Remember, transmission files start with the word
'transmit' and are saved in the directory C:\program files\seaLandings\transmissions.
After you've transmitted the report, you can save and print the fish ticket by highlighting one of CFEC lines and
clicking on the Fish Ticket button.
A fish ticket will be saved in your directory C:\Program Files\seaLandings\pdf.